- Read Time: 8 mins
- Hits: 14016
Working with sharp tool blades is a MUST in the workshop. Not only is is safer, it is much easier on the woodworker who not only doesn't have to work so hard, but it also makes woodworking much more fun. There is nothing more frustrating than trying to plane a board, or carve out a mortise when you have a dull tool.
Sometimes we think our tool or blade is sharp but really it isn't. When you take a blade that you thought was sharp, then really sharpen it, you will not believe the difference in how easy it cuts and how much less work it is. For years I struggled with what I thought were plane blades that were - sharp enough - . I knew they weren't the sharpest, but I never bothered to take the time to sharpen them properly and always assumed that they were ok.
One day, while visiting another woodworker, who had just sharpened his plane blade, I asked him if I could try it out. I was completely astounded what a difference a really sharp blade was like. It wasn't long after I encountered a more mature woodworker, who I knew was an expert in sharpening, and asked him if he would sharpen my blades for me ... and I would pay him. A week later he called to have me come and pick up the blades and while I was at his shop, I asked if he would give be a lesson in how I could get good results, with the least fuss, and this is what this video is about.
What he showed me is the same thing I am going to show here, what I think is one of the easiest and cost effective ways of sharpening chisel and plane blades and similar blades. This is the best way that works for me, but other people will have many other ways that are also just as good and maybe even easier and I am confident they will all be sharing their expertise with us. There are MANY MANY different ways to sharpen chisels and plane blades, and some people make a real art out of sharpening. It becomes - their thing - in woodworking, and so this article details what I learned that afternoon. The first thing you need to do is ...
- Read Time: 5 mins
- Hits: 35114
Have you ever cut all the pieces for a woodworking project then tried to put them together and found that they just don't fit together nicely? Could it be that the one tool you rely on most, your square is not giving you a proper angle reading ?
One of the most frustrating things about woodworking, especially for new woodworkers, is when you are working away on your project and it comes to starting to put it together and it just doesn't fit nicely. There are gaps in the joints, some of the angles seem to be off a bit, it just isn't coming to gether nicely.
When this happens, you get out your square and start double checking your cuts and if your square is off to begin with, measured one way, your cuts will be perfect, but reverse the square and if the joint is WAY OFF when reversed, then your square is the problem, not your woodworking ability. In many cases when this happens, you cannot go back and re-set up the machinery and re-cut the wood because it will be too small, so now you have a very expesive stack of firewood, or more wood for your cut-off pile that hopefully you will have a use for one day.
One of the tools we use continuely in our work, often with out even thinking about it is the square. The lowly square has been around for ever and has remainend basically unchanged in thousands of years. Today, we can purchase all sorts of different variations of the square, large squares, small squares, adjustable squares ....
- Read Time: 6 mins
- Hits: 34631
Making jigs is one of the most common tasks for most woodworkers. Sometimes they are simple, sometimes not, sometimes they are used once but often they are used over and over again. Some of the most common jigs are associated with out stationary tools, like bandsaws, table saws, lathes, drill presses and so on. Many of the stationary tools that we use have mitre slots the are used for a few things, like mitre gauges, feather boards and other accessories that utilize this convenient slot.
Table saws are often picked on for making jigs where the mitre slots is used and when making jigs, it's ideal to be able to have some mitre gauge blanks on hand, rather than having to stop and make these as well as the jig.
- Read Time: 6 mins
- Hits: 12530
Surprisingly, many woodworkers do not have moisture meters, and of those who do own them, most seldom use them. With wood being as active as it is, it seems that using a moisture meter to help determine the amount of wood movement would be pretty important. To novice woodworkers, wood movement is something that is not well understood, but it is a very important component of woodworking and needs to be studied by any serious woodworker. As we all know, wood, even after it is cut is constantly either absorbing moisture or giving off moisture. This is the a nature of wood. The absorption of moisture is primarily taken in through the end grain of wood, but some moisture is absorbed through the side side grain as well.
The result of this moisture absorption is that the cells of the wood expand, and can, in some situations, damage woodworking projects by breaking glue joints, expanding doors, having some wood material bow, and generally making your hard created woodworking project distorted at the least and even destroyed in rare conditions.
But as everyone knows who is working with wood, movement needs to be understood in order without the wood coming apart on you or reacting in some way you don't know. Knowing how moisture meters work can help you understand how to use them properly ....