WoodWorkWeb - Woodworking Community

Bandsaw Blade Repair - How to Solder Bandsaw Blades

Read Time: 4 mins

I have only broken 3 bandsaw blades in my lifetime so haven't had much opportunity to fix them, but I decided to make an exception in this case because the blade I had was still quite new and still very sharp to it was a good chance to see if I could be fixed the blade which snapped at the weld joint. These smaller blades for my little 12 inch Delta bandsaw which doesn't use a lot of tension on the blade so I think I have a pretty fair chance of getting this to work.

Watch it on Youtube: https://youtu.be/mqhsZl_cseA

I know many of the bandsaw blades appear to be spot welded together and I don't happen to own a spot welder by I have read of people who have solder the ends together with good results, so that is what I am going to try.

Making a Mitre Sled Jig for the Table Saw

Read Time: 6 mins

Cutting Mitres on the table saw is not trick ... getting them accurate is a bit more challenging, especially if you are doing things like picture frames. I seem to make most of my angle cuts on the table saw at 45 degrees, which by chance is the same angle as picture frame sides, so this jig will do double duty for me.
The one thing I should add here in terms of making picture frames, getting the 45-degree angle is only half the battle, the other thing that is crucial in making picture frames is that each opposing side of the fame needs to be EXACTLY the same length or the corners will never line up.

Watch it on Youtube: https://youtu.be/3czW9oJS1Kc

This jig will make accurate 45-degree angles, and if you want to make picture frames you can use the stoppers to make sure the horizontal pieces and the vertical pieces, however long they are, can be cut at exactly the same length.

How to Make a Lazy Susan Turning Table - 2 TIERS!

Read Time: 4 mins

Lazy Susan's have got to be the handiest things for serving devices whether stand-alone or on a dining room table, a picnic table or on a snack table. The only real problem is that some of them can take up so much room ... but there is a way to economize on the size without giving up on the amount of serving space and that is my making another level to them.

Watch it on Youtube: https://youtu.be/YWqEpnE356w

I wasn't sure what kind of center I wanted for the upper level so decided to make a prototype before making a final version. My first version had a round center column which I did not keep on so wanted to try this style of having simple square wood, but with an arc cut into them to accommodate later bowls and serving dishes ...

Stop Slippery Wood Glue Ups: 5 Quick Gluing Hacks

Read Time: 5 mins

Wood gets slippery when glue is applied to it and sometimes trying to tame a wet slippery wood glue up can be messy and frustrating. The best way to tackle this problem is to assume every glue up will be slippery ... and almost all of them are, and prepare the wood in advance to prevent it from sliding out of place on you with several techniques.

Watch it on Youtube: https://youtu.be/AA3TviThJW4

The first thing to think about in helping to prevent slipper glue-ups is ... What is my margin of error? that means, do you have any extra wood on your glue up that is going to need to be cut off later and where exactly is that wood. Once you know this you can use any one of a few different anti-slip ideas ...

Jigsaw Template Jig: Make Duplicate & Repeatable Cuts with a Jigsaw.

Read Time: 6 mins

Jigsaws have been around for a long time and most workshops have one but most don't get a lot of use, except those times when you really need something that only a jigsaw can do. I always try to get the most from my tools and when Mark sent me a not about making a patterning jig for a jigsaw, I thought it would be a good idea to see if this would be one way of getting more use from a jigsaw.

Watch it on Youtube: https://youtu.be/ZBVm3zzoIE0

Like many jigs, I started off at the table saw after I selected my wood, which in this case was high quality 1/4" plywood that I could use as the base plate and the first thing I needed to cut was some strips that I could use to capture the jigsaw base plate to the 1/4" plywood material ...

Strength Testing Salt and Grit on Glue Joints

Read Time: 3 mins

For many years I have heard people using things like Salt and Sand as a medium between 2 boards being glued, to help eliminate the slippage that happens when we try to glue boards together. I have never used the technique but recently I have had a flurry of people asking me if the using Salt as a grit when gluing boards together, does that weaken the joint?

Watch it on Youtube: https://youtu.be/1Ai-IQvRDo4

It sounds plausible that it might, but it could also strength the joint ... or it might do nothing noticeable, but I will never know if I don't test it, so that's exactly what I set out to do ...

Page 48 of 103